1/8 Scale Affordable Brushless System Now Is Available!
Thunder Tiger Corp. is pleased to announce the brand new ACE RC brushless speed control and motor for 1/8 scale R/C vehicles. ESC is now available in 80A and 150A, in which the former is perfectly used for buggy and truggy while the latter is mainly used for power-on-demand monster trucks as well as 1/5 scale. The ACE RC IBL4020 2000Kv super brushless system not only provides amazing torque and speed potential for your 1/8 scale vehicle, but supplies a longer operation time due to less friction in the brushless motor compared with other sensored systems. Also ACE RC brushless speed control is compatible with all sensorless brushless motors and most of sensored brushless motors such as Novak, LPP, Feigao and etc. Moreover, ESC is bullet-proof itself with other multiple protection features such as voltage cut-off protection, over-heat protection, throttle signal loss protection, motor blocked protection and splash/dust proof cover. Our customer would breeze through the system setup with the programming card.
ACE RC PROGRAM CARD
1. Size: 88mmx58mmx14mm
2. Wight: 40g
PROGRAM THE ESC
Programmable Items List (The italics texts in the form are the default settings)
1. Running Mode
2. Drag Brake Force
3. Low Voltage Cut-Off Threshold
4. Start Mode(Punch)
5. Max Brake Force
6. Max Reverse Force
7. Initial Brake Force
8. Neutral Range
10. Over-heat Protection
11. Motor Rotation
12. Lipo Cells
*Note: The option “Auto Calculate” is only available for 2s, 4s and 6s Lipo. If the voltage of the battery pack is lower than 8.8V, it is judged as a 2s Lipo; If the voltage is between 8.8V to 17.6V, it is judged as a 4s Lipo; If the voltage is higher than 17.6V, it is judged as a 6S Lipo. So in order to make the Low Voltage Cutoff Protection function always works correctly, please set the “Lipo Cells” item manually.
The program card is ONLY suitable for the ESC of BLC-80C, BLC-150C, BLC-80C Plus, BLC-150C Plus.
Please refer to the user manual of the ESC for detail information about each programmable item.
■ When you are using an ESC with a built-in BEC(Battery Elimination Circuit)
a) Disconnect the power pack from the ESC.
b) Disconnect the BEC cable of the ESC(trio wires) from your receiver, then connect it to the program card at the top right corner position marked with .
c) Connect the main power pack to the ESC.
d) After several seconds, the digit LEDs on the program card light to show the current programmable value of the ESC.
Note 1: The sequence of step b) and step c) cannot be reversed! Otherwise the program card cannot work properly.
Note 2: It takes several seconds for program card to communicate with speed controller before the LEDs lights, please wait patiently.
■ When you are using an ESC without a built-in BEC
If the ESC hasn’t a built-in BEC, you must use an additional battery pack (4.8V-6V) to power the program card. Please connect the battery to the program card at the top right corner position marked with .
Usually, a receiver battery pack is a good choice.
a) Disconnect the power pack from the ESC.
b) Disconnect the BEC cable of the ESC(trio wires) from your receiver, then connect the BEC cable or the individual data cable (Please refer to the following Note4) to the program card at the top right corner position marked with .
c) Connect the additional battery pack to the program card at the top right corner.
d) Connect the main power pack to the ESC.
e) After several seconds, the digit LEDs on the program card light to show the current programmable value of the ESC.
Note 3: The sequence of step b), c) and step d) cannot be reversed! Otherwise the program card cannot work properly.
Note 4: For ESC with an individual data cable (that is a short trio wire just nearby the BEC cable of the ESC), you need to connect the program card with this individual date cable, while not the BEC cable.
Warning: Do not use a battery pack more than 6V to supply the program card!
Press the “ITEM” button to select the programmable items in a loop. The serial number of the programmable items will be shown by 2 digit LEDs marked with “ITEM”, and the current value corresponding to the selected programmable item will be shown by another digit LED marked with “VALUE”. Press the “VALUE” button to choose the parameter value you need. After that, press the “OK” button, a bright “－” symbol appears in the middle position of the digit LED marked with “VALUE” for about 1-2 seconds, that means the new setting is accepted and stored in the ESC.
The “RESET” button is used for restoring all the items of the ESC to the default vales.
Thunder Tiger strives to bring you the highest level of quality and service we can provide. We test our products around the world to bring you the state-of-art items. Thunder Tiger guarantees that you should enjoy many hours of trouble free use from our R/C products. Thunder Tiger products have been sold worldwide through the authorized distributors that are supported directly and rapidly form Thunder Tiger. You may find that Thunder Tiger is always pursuing to explore new items creatively with highest quality. To update the latest product information and to get the best technical support, please feel free to contact your local hobby shops or Thunder Tiger authorized distributor.
FUNCTIONS AND FEATURES
program card for the brushless ESC (Electronic Speed Controller). The program card has a friendly user interface, so you can easily set the programmable parameters of the ESC with this device. It is pocket-sized, so you can bring it to the racing field conveniently.